Soil Salinity Testing, Data Interpretation and Recommendations (C 1019) University of Georgia Extension The University of Georgia Agricultural and Environmental Services Laboratories offer soil salinity testing to help farmers and the general public diagnose and manage problems associated with soil salinity. By definition, a saline soil contains excess soluble salts that reduce the growth of most crops or ornamental plants. This publication discusses soil salinity testing, data interpretation and recommendations, specifically those pertaining to the University of Georgia. 2016-06-13 16:10:22.61 2012-06-06 14:07:24.0 Soil Salinity Testing, Data Interpretation and Recommendations | Publications | UGA Extension Skip to content

Soil Salinity Testing, Data Interpretation and Recommendations (C 1019)

Download PDF

Leticia S. Sonon, Uttam Saha, and David E. Kissel
Agricultural and Environmental Services Laboratories

The University of Georgia Agricultural and Environmental Services Laboratories offer soil salinity testing to help farmers and the general public diagnose and manage problems associated with soil salinity. By definition, a saline soil contains excess soluble salts that reduce the growth of most crops or ornamental plants. These soluble salts contain cations such as sodium (Na+), potassium (K+), calcium (Ca2+) and magnesium (Mg2+) along with anions chloride (Cl-), sulfate (SO42-), nitrate (NO3-), bicarbonate (HCO3-) and carbonate (CO32-).

illustration showing difference between good and poor soil structure. The good structure has more space between soil particles. Left: Soil with good structure (non-sodic soil).
Right: Soil with poor and dense structure (sodic soil).

Soil salinity is caused by several factors. Soils may become saline as a result of land use, including the use of irrigation water with high levels of salt. Seawater is also a source of salts in low-lying areas along the coast through tidal estuaries or when rainfall in coastal regions mixes with sea spray. Saltwater intrusion into freshwater aquifers may occur when wells are close to the coast and water is pumped to the surface for various purposes, including irrigation. Irrigating from salt-impacted wells or saline industrial water may lead to the formation of saline soils.

Soil sodicity, on the other hand, is caused by high sodium levels in soils at concentrations greater than 15 percent of the cation exchange capacity. Sodic soils tend to have poor structure with unfavorable physical properties such as poor water infiltration and air exchange, which can reduce plant growth.

Effects of Salinity on Plant Growth

Salinity reduces water availability for plant use. High salt levels hinder water absorption, inducing physiological drought in the plant. The soil may contain adequate water, but plant roots are unable to absorb the water due to unfavorable osmotic pressure. This is referred to as the osmotic or water-deficit effect of salinity. Plants are generally most sensitive to salinity during germination and early growth.

The second effect of salinity is shown when excessive amounts of salt enter the plant in the transpiration stream and injure leaf cells, which further reduces growth. This is called the salt-specific or ion-excess effect of salinity (Greenway and Munns, 1980). Symptoms may include restricted root growth, marginal or leaf tip burning/ browning, inhibited flowering, reduced vigor and reduced crop yields.

Visual Diagnosis of Salt-Affected Soils

Accumulation of salts can result in three soil conditions: saline, saline-sodic and sodic soils. Each of these soil conditions has distinct characteristics that can be observed in the field, which are useful for diagnosing the problem. Completely white soils are saline, soils with a brownish-black crust are sodic, and grey-colored soils are generally saline-sodic. The following physical observations/symptoms may be helpful in diagnosing salt-related soil problems:

Problem Symptoms
Saline White crust on soil surface. Water-stressed plants. Leaf tip burn.
Sodic Poor drainage. Black powdery residue on soil surface.
Saline-Sodic Grey-colored soil. Plants showing water stress.
Source: Waskom et al., 2010. Diagnosing saline and sodic soil problems. Colorado State University Extension Fact Sheet # 0.521

Soil Salinity Measurements

Problems due to soil salinity and sodicity in soil are commonly evaluated by laboratory testing. The following laboratory measurements are typically used to determine the extent of these problems:

1. Electrical Conductivity (EC) — Measures the ability of the soil solution to conduct electricity and is expressed in decisiemens per meter (dS/m, which is equivalent to mmhos/cm). Because pure water is a poor conductor of electricity, increases in soluble salts result in proportional increases in the solution EC. The standard procedure for salinity testing is to measure EC of a solution extracted from a soil wetted to a "saturation paste." According to U.S. Salinity Laboratory Staff (1954), a saline soil has an EC of the saturated paste extract of more than 4 dS/m, a value that corresponds to approximately 40 mmol salts per liter. Crops vary in their tolerance to salinity and some may be adversely affected at ECs less than 4 dS/m. Salt tolerances are known for common crops. For example, peach is sensitive, whereas cotton is more salt tolerant (Maas, 1990). Beets and asparagus are very tolerant of salinity.

2. Total Soluble Salts (TSS) — Refers to the total amount of soluble salts in a soil-saturated paste extract expressed in parts per million or milligrams per liter (ppm or mg/L). A linear relationship exists between TSS and EC within a certain range that can be useful to closely estimate soluble salts in a soil solution or extract. The ratio of TSS to EC of various salt solutions ranges from 550 to 700 ppm per dS/m. Sodium chloride, the most common salt, has a TSS of 640 ppm per dS/m. So if EC is known, TSS can be estimated using the formula below:

TSS (mg/L or ppm) = EC (mmhos/cm or dS/m) x 640

3. Sodium Adsorption Ratio (SAR) — A widely accepted index for characterizing soil sodicity, which describes the proportion of sodium to calcium and magnesium in soil solution. The formula to calculate SAR is given below, with concentrations expressed in milliequivalents per liter (meq/L) analyzed from a saturated paste soil extract.

Equation to calculate Sodium Adsorption Ratio. SAR = [Na+] divided by the square root of 1/2([Ca2+] + [Mg2+])

When SAR is greater than 13, the soil is called a sodic soil. Excess sodium in sodic soils causes soil particles to repel each other, preventing the formation of soil aggregates. This results in a very tight soil structure with poor water infiltration, poor aeration and surface crusting, which makes tillage difficult and restricts seedling emergence and root growth (Munshower, 1994; Seelig, 2000; Horneck et al., 2007).

4. Exchangeable Sodium Percentage (ESP) — Another index that characterizes soil sodicity. As noted above, excess sodium causes poor water movement and poor aeration. By definition, sodic soil has an ESP greater than 15 (US Salinity Lab Staff, 1954). ESP is the sodium adsorbed on soil particles as a percentage of the Cation Exchange Capacity (CEC). It is calculated as:

ESP = [Na2+] x 100

CEC is often estimated as the sum of the major exchangeable cations, including hydrogen. Both cations and CEC are expressed as meq/100g. ESP can also be calculated as:

ESP = [Na2+] x 100
[Ca2+ + Mg2+ + NA+ + K+]

ESP is used to characterize the sodicity of soils only, whereas SAR is applicable to both soil and soil solution or irrigation water.

The Natural Resources Conservation Service (NRCS) provides the following classification of salt-affected soils using the saturated paste extraction:

Class EC
SAR ESP Typical soil structural condition*
Normal Below 4.0 Below 13 Below 15 Flocculated
Saline Above 4.0 Below 13 Below 15 Flocculated
Sodic Below 4.0 Above 13 Above 15 Dispersed
Saline-Sodic Above 4.0 Above 13 Above 15 Flocculated
*Soil structural condition also depends on other factors not included in the NRCS classification system, including soil organic matter, soil texture and EC of irrigation water (Horneck et al., 2007).

Collecting Soil Samples for Salinity Testing

The goal of salinity testing is to determine the salt level of soil from which roots extract water. Therefore, soil samples should be collected from the 0 to 6 inch depth or from the rooting depth. Deeper samples may be collected if the goal is to identify the extent of salinity caused by irrigation within the soil profile. In many cases, comparing soil samples from the affected area to surrounding normal-looking areas is valuable in diagnosing the problem. Collect eight to 10 cores from around a uniform area, mix them in a clean plastic bucket and transfer a composite sample (approximately 1 pound) to a soil sample bag.

Soil Salinity Test Package Offered at UGA

I. Basic Soil Salinity Test (1:2 soil-to-water ratio).

Because methods of obtaining soil solution samples at water contents more typical of the field condition (the saturated paste) are not very practical, aqueous extracts of the soil samples have traditionally been made in the laboratory at higher-than-normal water contents for routine soil salinity diagnosis and characterization. However, the values from the 1:2 soil-to-water extraction are different from the standard saturated paste extraction. Therefore, the interpretation shown below would also be different. The following parameters are included in the basic soil salinity test:

  • Calcium (Ca2+)
  • Magnesium (Mg2+)
  • Potassium (K+)
  • Sodium (Na+)
  • pH
  • Electrical Conductivity (EC)
  • Total Soluble Salts (TSS)
  • Sodium Adsorption Ratio (SAR)

The University of Georgia adopted the following guidelines in interpreting EC data from soil extracts (1:2 soil-to-water ratio).

Electrical Conductivity
Rating Interpretation
0-0.15 Very low Plants may be starved of nutrients.
0.15-0.50 Low If soil lacks organic matter.
Satisfactory if soil is high in organic matter
0.51-1.25 Medium Okay range for established plants.
1.26-1.75 High Okay for most established plants.
Too high for seedlings or cuttings.
1.76-2.00 Very high Plants usually stunted or chlorotic.
> 2.00 Excessively high Plants severely dwarfed; seedlings and rooted cuttings frequently killed.

II. Comprehensive Soil Salinity Test (Saturated Paste Extract; NH4OAc Extraction for ESP).

The saturated paste method provides a more representative measurement of total soluble salts in the soil solution because it is closer to the water content of the soil under field conditions. This method, however, is time-consuming and subject to some technician variability when preparing the paste. This test package also includes extraction of soils with ammonium acetate (NH4OAc) to measure exchangeable cations and ESP.

Photo od saturated pastes in beakers. Preparing saturated pastes.

The following parameters are included in the comprehensive soil salinity test:

1. Saturated Paste Extract

  • Calcium (Ca2+)
  • Magnesium (Mg2+)
  • Potassium (K+)
  • Chloride (Cl-)
  • Sodium (Na+)
  • Nitrate-nitrogen (NO3-N)
  • Sulfate (SO42-)
  • pH
  • Electrical Conductivity (EC)
  • Total Soluble Salts (TSS)
  • Sodium Adsorption Ratio (SAR)

2. NH4OAc Extract

  • Calcium (Ca2+)
  • Magnesium (Mg2+)
  • Sodium (Na+)
  • Potassium (K+)
  • Exchangeable Sodium Percentage (ESP)

The general interpretation of data on electrical conductivity and exchangeable sodium percentage from saturated paste extracts are given below.

Interpretation of electrical conductivity (EC) from saturated paste extract.
Electrical conductivity
Salt Rank Interpretation
0-2 Low Very little chance of injury on all plants.
2-4 Moderate Sensitive plants and seedlings of others may show injury.
4-8 High Most non-salt tolerant plants will show injury; salt-sensitive plants will show severe injury.
8-16 Excessive Salt-tolerant plants will grow; most others show severe injury.
16+ Very Excessive Very few plants will tolerate and grow.
Source: Lamond, R. and D.A. Whitney. 1992. Management of saline and sodic soils. Kansas State University, Department of Agronomy MF-1022.
Interpretation of exchangeable sodium percentage (ESP) from saturated paste extract.
ESP Rank Interpretation
0-10 Low No adverse effect on soil is likely.
10+ Excessive Soil dispersion resulting in poor soil physical condition and poor plant growth are likely.
Source: Lamond, R. and D.A. Whitney. 1992. Management of saline and sodic soils. Kansas State University, Department of Agronomy MF-1022.

Reclaiming Salt-Affected Soils

After the kinds and amounts of salts in the soil have been determined by testing, the soil can be properly treated. Reclaiming a salt-affected soil involves leaching, chemical treatment or a combination of both.


Application of good quality irrigation water in the correct amounts will remove excess salts from soils that are well structured and have good internal drainage. Excess salts should be leached below the root zone so that the EC of the soil solution becomes lower than the crop's critical threshold. The University of Georgia recommends leaching techniques to remove salts from the root zone when EC is greater than 1.25 mmhos/cm at a soil-to-water ratio of 1:2. The volume of low-salt water needed to dissolve and leach any large quantities of salts from the soil is given below. A general rule of thumb is that 6 inches of water will remove about half of the salt, 12 inches will remove 4/5, and 24 inches will remove 9/10.

Estimated leaching requirements to remove salts
Volume of salt-free water Reduction of salt content in soil
6 inches 50%
12 inches 80%
24 inches 90%

For soils with poor drainage, it is recommended to break root-restrictive hardpans or clay pans by deep tillage to allow water to penetrate and leach the salts. It may be necessary to install tile drains to remove salt-laden drainage water and move it below the root zone by rainfall or irrigation water.

Chemical treatment

When a soil has an SAR value of above 13 (or ESP greater than 15), it contains excess sodium that makes it a sodic soil. Excess sodium can cause soil dispersion, which prevents the formation of soil aggregates, resulting in surface sealing or crusting. Dispersion of the soil by excess sodium reduces water infiltration and movement through the soil, and also causes poor aeration. Good aeration and water movement are both essential to unrestricted growth of plant roots. To eliminate surface sealing, the soil should be treated with calcium to remove sodium. One of the most commonly used calcium sources for correcting sodium-contaminated soil is gypsum (calcium sulfate, Ca[SO4]•2[H2O]). Gypsum is incorporated into the soil, followed by application of salt-free irrigation water. The amount of calcium to apply depends on the quantity of sodium in the soil. Road de-icing salt or calcium chloride (CaCl2) is also an option to provide calcium to soil, but it is more expensive than gypsum.

The table below provides the amount of gypsum needed to replace exchangeable sodium in the soil. The soil test sodium values are determined from an ammonium acetate extraction at pH 7.

Soil exchangeable
Amount of Gypsum Neededa
lbs/acre Tons/acre-footb Tons/acre-6 inchesc lbs/1000 ft2-1 foot lbs/1000 ft2-6 inches
460 1.7 0.9 80 40
920 3.4 1.7 160 80
1380 5.2 2.6 240 120
1840 6.9 3.4 320 160
2300 8.6 4.3 400 200
2760 10.3 5.2 480 240
Source: U.S. Salinity Laboratory Staff, 1954, with modifications.
a The amounts of gypsum are given to the nearest 0.1 ton.
b 1 acre-foot of soil weighs approximately 4,000,000 pounds.
c 1 acre-6 inches of soil weighs approximately 2,000,000 pounds.

Correcting a salt-affected soil involves identifying the kind and amount of salt, chemical treatment and leaching. When a salinity problem is identified, it is recommended that corrective steps be taken immediately. Prompt action will give a better chance of reclaiming the affected soil, be less expensive and pose less risk of plant damage.


Greenway H., Munns R. 1980. Mechanisms of salt tolerance in nonhalophytes. Annu. Rev. Plant Physiol. 31:149-190.

Horneck, D.S., Ellsworth, J.W., Hopkins, B.G., Sullivan, D.M., Stevens, R.G., 2007. Managing Salt-Affected Soils for Crop Production. PNW 601-E. Oregon State University, University of Idaho, Washington State University.

Lamond, R. and D.A. Whitney. 1992. Management of saline and sodic soils. Kansas State University, Department of Agronomy MF-1022.

Maas, E.V. 1990. Crop salt tolerance. In Agricultural Salinity Assessment and Management. K.K. Tanji (Ed) American Society of Civil Engineers.

Munshower, F.F. 1994. Practical Handbook of Disturbed Land Revegetation. Lewis Publisher, Boca Raton, FL.

Seelig, B.D. 2000. Salinity and Sodicity in North Dakota Soils. EB-57. North Dakota State University, Fargo, ND.

US Salinity Laboratory Staff. 1954. Diagnosis and improvement of saline and alkali soils. USDA Agricultural Handbook No. 60. U.S. Government Printing Office. Washington, DC.

Waskom, R.M., T.A. Bauder, J.G. Davis, and G.E. Cardon. 2010. Diagnosing saline and sodic soil problems. Colorado State University Extension Fact Sheet # 0.521.

Status and Revision History
Published on May 31, 2012
Reviewed on Oct 5, 2015